suse νισάφι πια ρε παιδια!!!

[jim_p]

Τιποτα?! Δεν ξερω πως κλεινει ο network manager σε opensuse για να σου πω να ξαναδοκιμασεις με τον nm κλειστο!

 

Επισης

- "τιποτα" οπως λεμε "command not found"?

- "τιποτα" οπως λεμε "δεν βλεπει καποιο δικτυο γυρω του"?

- "τιποτα" οπως λεμε "δεν εχει καν το ασυρματο interface, ειτε αυτο ονομαζεται wlan0 ειτε wmaster0 κλπ"?

 

Ξαναεπισημαινω οτι το τρεχεις σαν root.

 

Το δικο μου iwlist scan απο το λαπτοπ με την χαλια καρτα της inprocomm

># iwlist scan
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

[b]wlan0     Scan completed :
         Cell 01 - Address: 00:15:56:B6:0C:B3
                   ESSID:"OTENET_9956"
                   Protocol:IEEE 802.11g
                   Mode:Managed
                   Frequency:2.447 GHz (Channel 8)
                   Quality:67/100  Signal level:-53 dBm  Noise level:-96 dBm
                   Encryption key:on
                   Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                             9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
                             48 Mb/s; 54 Mb/s
                   Extra:bcn_int=100
                   Extra:atim=0[/b]

vboxnet0  Interface doesn't support scanning.

[ZELDA]

> iw list scan
Usage:	iw [options] command
Options:
--debug		enable netlink debugging
--version	show version (0.9.15)
Commands:
help
event [-t] [-f]
phy <phyname> info
list
phy
phy <phyname> set name <new name>
phy <phyname> set freq <freq> [HT20|HT40+|HT40-]
dev <devname> set freq <freq> [HT20|HT40+|HT40-]
phy <phyname> set channel <channel> [HT20|HT40+|HT40-]
dev <devname> set channel <channel> [HT20|HT40+|HT40-]
phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [flags <flag>*]
dev <devname> interface add <name> type <type> [mesh_id <meshid>] [flags <flag>*]
dev <devname> del
dev <devname> info
dev <devname> set monitor <flag>*
dev <devname> set meshid <meshid>
dev
dev <devname> set type <type>
dev <devname> ibss leave
dev <devname> ibss join <SSID> <freq in MHz> [fixed-freq] [<fixed bssid>] [key d:0:abcde]
dev <devname> station get <MAC address>
dev <devname> station del <MAC address>
dev <devname> station set <MAC address> plink_action <open|block>
dev <devname> station dump
dev <devname> set mesh_param <param> <value>
dev <devname> get mesh_param <param>
dev <devname> mpath get <MAC address>
dev <devname> mpath del <MAC address>
dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address>
dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address>
dev <devname> mpath dump
dev <devname> scan trigger [freq <freq>*] [ssid <ssid>*|passive]
dev <devname> scan dump [-u]
dev <devname> scan [-u] [freq <freq>*] [ssid <ssid>*|passive]
reg set <ISO/IEC 3166-1 alpha2>
reg get
dev <devname> disconnect
dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465]

You can omit the 'phy' or 'dev' if the identification is unique,
e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.)

με την εντολη iwlist scan δες παιρνω τιποτα με iw list scan παιρνω αυτο .

[jim_p]

Η εντολη που βαζεις τοτε ειναι η "iw" (σκετο) και επειδη δεν δεχεται σαν παραμετρο το list και το scan βγαζει οτι βλεπεις (το --help της).

 

Απο το "man iw"

iw - show / manipulate wireless devices and their configuration

 

Η "iwlist" περιεχεται στο πακετο wireless-tools, τουλαχιστον εδω στο debian. Αν δεν το εχει, βαλτο.